How to Apply

Using heat resistant spray paint to paint internal flue pipe or a stove.

 
  stove quote 1
 

Hold the can about 300mm away.......several thin coats will give you a better finish......The can can be easily warmed up by holding it in warm water......Before starting shake the can for at least 2 minutes.....

stove quote 2  
 

Our heat resistant spray paint comes in a wide variety of colours but by far the most popular color is matt black. Many people spray their flue pipe with matt black heat resistant spray paint to match their stove. Our heat resistant spray paint is designed for working temperatures of up to 1200°F.

You should not paint flue pipe before it is in place. This is because the paint goes through it's final curing process when it gets hot. Until it gets hot the paint is easy to scratch so if you paint it before it is installed you are bound to scratch and mark it.

Make sure that the surfaces you are painting are clean, and free of dust and grease. Spray onto a bit of scrap or newspaper to start with as it is possible that there is un mixed paint in the tube - this will clear it out. Hold the can about 300mm away from the surface you are painting: any closer and the paint is likely to pool, any further away and the paint may dry before it hits the surface. Applying the paint in several thin coats will give you a better finish than one thick coat.

Painting is best done at or above room temperature - around 20°C is ideal. Do not spray if the temperature is below 5°C.

Before starting shake the can for at least 2 minutes. This is especially important for lighter shades of paint. If the can is cold you will need to warm it up. The can can be easily warmed up by holding it in warm water for a few minutes.

When you have finished using the heat resistant spray paint hold the can upside down and spray onto some scrap or a bit of newspaper. This will clear the nozzle and tube of spray leaving it clear for the next time you want to use it.

If you are painting a surface that has already been painted with heat resistant spray paint then only respray it once. Any more coats and the paint is liable to peel off. If you have to spray over a surface that has already been spray twice then you will need to strip off the old paint using sandpaper or a solvent.

 
  stove quote 1
 

the paint may steam a little as it cures and may also give off an odd smell. This is normal

stove quote 2  
 

When you light the stove for the first few times the paint may steam a little as it cures and may also give off an odd smell. This is normal and we recommend that you ventilate the room during these firings until the smell no longer appears.

Problems with heat resistant spray paint

If the paint peels off or cracks then it is likely that you have applied to too thickly. If the paint comes off in big sheets then it is likely that you did not clean the surface well enough. If rust comes through the paint then it is likely that you did not clean the rust off well enough.

Painting twin wall flue pipe internally

The natural finish of the outer skin of our twin wall flue pipe is a satin stainless steel and if desired it can be painted using heat resistant spray paint where it passes through the internal part of the building.

Painting twin wall flue pipe externally

 
  stove quote 1
 

heat resistant spray paint is not really suitable for use externally......after a number of years it will peel off.......apply a coat of suitable exterior paint like hammerite or smoothrite

stove quote 2  
 

Our heat resistant spray paint is not really suitable for use externally. You will find that after a number of years it will peel off exposing the stainless steel underneath.

Where the external portion of the chimney needs painting it should first be degreased, given a key with wire wool, then a coat of etching primer should be applied, and finally apply a coat of suitable exterior paint like hammerite or smoothrite. If you do not want to do this on site then the relevant pipes can be taken to a car body paint shop. You can also have the flue powder coated. Remember to mask off the ends of the flue pipe and block the ends up so that paint cannot get inside the pipe.
Note where the chimney passes close to anything combustible it should not be painted.